MK3S+ extruder printed parts for Mosquito
I have a Mosquito that has been sitting in a box for a few years, and I just now getting around to installing it on my Prusa MK3S+. I don't have the printed parts that come with the Mosquito upgrade kit. Does Slice provide downloads for printing yourself?
Just received my PRP. Do I paint over the nozzle hole?
Hi everyone, just received my PRP and really excited to try it after lots of PETG blobbing. This might be a stupid question, but I was wondering, do you just paint the entire nozzle (including the hot end / hot end hole?), or should you be careful and
Heater Cartridge Removal
I am trying to remove a heater cartridge from a Mosquito hotend and it is very stuck. I am not sure that the heater unseater is the correct tool or how it would work. Any tips for removing the stuck heater cartridge without damaging the hotend?
Does any of the Hotends from Slice Engineering work w/ the Monoprice Maker Select Plus?
I just got a new printer for testing and I wanted to upgrade it. The printer is called Monoprice Maker Select Plus and I wanted to see if any parts from Slice Engineering would work on this specific printer... Seth
Mosquito Hot End which way?? please help!
Hello, I just purchased a Mosquito hot End for my Tevo Tarantula Pro. I am designing a carriage mount that can be 3-D printed( obviously!!). I'm not sure which way to place the Mosquito, looking at the heat sink, or looking at the Mosquito logo?? Please help! the fan ducked I an designing comes very close to the side of the heat block, and I don't want it to melt. should it be placed in the front, or the heat sink side?
Boron Nitride Paste
Good Morning All, I put the paste on an old thermistor, for the hot end and just bought a new one. How do I remove the old thermistor with the paste? Thanking you in advance, gyrene2083
Using Copperhead Heatbreak with Prusa I3 MK3S heat sink and hot block
Hi there, I purchased a Copperhead Threaded Reprap 1.75 (compatible with the MK3S) heat break. When installing it with the Prusa e3d V6 hot block and nozzle i noticed that the hot end of the heat break is longer than the e3d heat break by about 1.5 mm and pokes out of the hot block. Is this okay? Thank you! Jesse Riley
Copperhead Slicone Boot
Is the boot required for the copperhead? I have a Ender 3V2 with Copperhead Heartbreak, and I recently added the copperhead hot block and silicone boot. Problem I am having is cooling Since the copperhead is much wider than the stock block, I am having
Older Model Printers/PrintrBot 1403 Simple Metal and Copperhead
Hello, I am fitting new ideas to an older model printer. I have a PrintrBot 1403 Simple Metal. I am mechanically changing it slowly and adding in more options for larger builds. I had come across this company, Slice Engineering, b/c I wanted a few parts
Identifying vanadium nozzles
Hi, I have a few vanadium and bridge master nozzles, but am having difficulty telling them apart. I'm about to do some PETG-CF printing and keen not to destroy my bridgemaster nozzles. Is there any identifying mark, scratch test, or way to clearly distinguish
mosquito onto anycubic kobra max
My kobra max has a volcano style hotend from the factory and I would like to upgrade to a mosquito. I was wondering if anyone makes adapter brackets going from volcano style to mosquito style. I don't want a decrease in speed capabilities so I'm not sure
How do I install ddx copperhead onto DDX extruder?
I've searched high and low and I can't find installation instructions for a ddx copperhead onto a DDX extruder. Can someone point me to them?
Typical Feed Rate for PLA?
I've just made a new printer with a Mosquito with 0.4mm CHT nozzle, a Voron silicon sock 50W bond tech heater and a 300C thermistor. The feed rate seems like it could be a bit slow. It's probably half of what I'd expect. I'm printing 1.75 PLA at 210c
Air Gap in Heatsink
Hello folks, This is a long winded way to ask what is probably a simple question with a simple answer. The context: I recently purchased the Copperhead as an upgrade for the Anycubic Vyper. The Vyper's stock hotend has the sort of design where the bowden
Mosquito Magnum PETG max flow rate?
What is the max flow rate in the Mosquito Magnum for PETG? I purchased the Mosquito Magnum with the impression that it would provide much greater flow rate than the stock Prusa V6 hot end. The most I have been able to reliably push through the hot end
Prusa Mini heatbreak
Is there a bimetallic heatbreak available for the Mini without a whole hotend?
Print Speed with Mosquito Magnum and 1mm+ Nozzles?
With the Magnum and a 1.0 - 1.6mm nozzle what sort of print speed can be expected before the hot end cannot keep up?
Simplify 3D
Any chance. of publishing some optimized S3D profiles? And/Or calculations for volumes and speed and nozzle by size, Tutorials etc. I want to get the most from my mosquito magnum and Bontech DDX
dual fans
dual fans for better cooling, push/pull. Good or not good? Hope to reach 400 C.
Can I use the Mosquito™ hotend with a threaded-style extruder?
Can I use the Mosquito™ hotend with a threaded-style extruder?